Lean Systems Engineering Technology, B.S.

Degree Requirements

Students complete the first two years at the Bluegrass Community and Technical College (BCTC) and earn an Associate in Applied Science (A.A.S.) in Integrated Engineering Technology. They will then transfer to the University of Kentucky for their junior and senior years to earn Bachelor of Science in Lean Systems Engineering Technology.

In addition to the University graduation requirements listed in the Graduation Requirements section of College of Engineering Bulletin, to be awarded a Bachelor of Science degree in any field of engineering or Computer Science, a student must:

1. complete the University and College requirements relating to writing and the UK Core.
2. complete the required number of hours, exclusive of those earned in freshman college algebra and freshman college trigonometry, with a cumulative standing of not less than 2.0 on a 4.0 scale.
3. complete a minimum of 24 credit hours of departmental courses at or above the 300 level.
4. complete all departmental courses and technical electives with a cumulative standing of 2.0 or higher.
5. complete any additional departmental graduation requirements.

Each student must complete the following:

UK Core Requirements

See the UK Core  section of this Bulletin for the Complete UK Core  requirements. Students will complete BCTC’s general education requirements which will fulfill UK’s Core requirements via the GETA transfer agreement, except for Arts & Creativity.

Graduation Composition and Communication Requirement (GCCR)

• LST 409 - CAPSTONE I Credit(s): 3

Premajor Requirements

NOTE: Students take the premajor courses below at Bluegrass Community and Technical College:

• MAT 126 - TECHNICAL ALGEBRA AND TRIGONOMETRY Credit(s): 3
• ENG 101 - WRITING I Credit(s): 3
• IET 111 - LEAN SAFETY CULTURE Credit(s): 1
• IET 207 - ELECTRO-HYDRAULICS/PNEUMATICS Credit(s): 4
• IET 121 - BASIC ELECTRICITY Credit(s): 4
• IET 202 - MOTOR CONTROLS AND SENSING DEVICES Credit(s): 4
• IET 208 - MECHANICAL DRIVE SYSTEMS Credit(s): 4
• IET 112 - LEAN MANUFACTURING CONCEPTS Credit(s): 1

•  

• PHY 151 - INTRODUCTION TO PHYSICS Credit(s): 3

• OR

• PHY 152 - INTRODUCTION TO PHYSICS Credit(s): 3

•  

• ENG 102 - WRITING II Credit(s): 3
• MAT 170 - ELEMENTARY CALCULUS AND ITS APPLICATIONS (prereq: MAT 150) Credit(s): 3
• IET 104 - BLUEPRINT READING/SCHEMATICS Credit(s): 2
• IET 128 - MACHINE TOOL OPERATIONS Credit(s): 3
• IET 113 - LEAN 5S METHODOLOGY I Credit(s): 1
• IET 204 - AUTOMATED MOTOR CONTROLS Credit(s): 6
• IET 114 - LEAN PROBLEM SOLVING METHODOLOGY Credit(s): 1
• CAD 100 - INTRODUCTION TO CAD Credit(s): 3
• UK CORE - ORAL COMMUNICATIONS Credit(s): 3
• UK CORE - SOCIAL AND BEHAVIORIAL SCIENCE (not SOC) Credit(s): 3
• IET 110 - WELDING AND FABRICATION Credit(s): 4
• IET 205 - ROBOT MAINTENANCE Credit(s): 5
• IET 115 - LEAN MACHINE RELIABILITY Credit(s): 1
• UK CORE - HERITAGE Credit(s): 3
• UK CORE - SOCIAL AND BEHAVIORAL Credit(s): 3

Major Requirements

• ME 205 - COMPUTER AIDED ENGINEERING GRAPHICS Credit(s): 3
• WRD 204 - TECHNICAL WRITING Credit(s): 3
• UK CORE - ARTS AND CREATIVITY Credit(s): 3
• LST 301 - INTRODUCTION TO JUST-IN-TIME Credit(s): 3
• LST 302 - MANUFACTURING SIMULATION AND MATERIAL & INFORMATION FLOW CHARTS Credit(s): 4
• LST 303 - INTRODUCTION TO ABNORMALITY MANAGEMENT Credit(s): 4
• LST 304 - INTRODUCTION TO PRODUCTIVITY IMPROVEMENT Credit(s): 4
• LST 305 - SYSTEM OF QUALITY ASSURANCE & BUILT-IN-QUALITY Credit(s): 4
• LST 306 - KAIZEN OF STANDARDIZED WORK Credit(s): 4
• LST 409 - CAPSTONE I Credit(s): 3
• LST 406 - PROBLEM SOLVING II Credit(s): 4
• LST 403 - PRODUCTION INSTRUCTION, SMALL LOT PRODUCTION & CHANGE OVER PROCESSES Credit(s): 4
• LST 410 - CAPSTONE II Credit(s): 3
• LST 404 - LOGISTICS Credit(s): 3
• LST 405 - MANAGING THE SHOP FLOOR AND LEADING KAIZEN Credit(s): 4

Guided Electives

A minimum of 3 hours can be selected by the student. The technical electives allow the student an opportunity to concentrate or gain depth in one or more of the various specialty areas of lean systems engineering technology. The technical electives must be selected from the courses listed below and approved by the student’s academic advisor. Other courses may be considered, each on its individual merit.

Approved Technical Electives:

• CPT 300 - ANALYTICAL METHODS IN ENGINEERING TECHNOLOGY Credit(s): 3

• OR

• LST 300 - ANALYTICAL METHODS IN ENGINEERING TECHNOLOGY Credit(s): 3

•  

• CPT 400 - ENGINEERING ECONOMICS Credit(s): 2

• OR

• LST 400 - ENGINEERING ECONOMICS Credit(s): 2

•  

• CPT 401 - ENGINEERING ANALYSIS & APPLICATIONS Credit(s): 3

• OR

• LST 401 - ENGINEERING ANALYSIS & APPLICATIONS Credit(s): 3

•  

• CPT 402 - FUNDAMENTALS OF OSHA Credit(s): 2

• OR

• LST 402 - FUNDAMENTALS OF OSHA Credit(s): 2

•  

• CPT 425 - PROJECT MANAGEMENT Credit(s): 3

• OR

• LST 425 - PROJECT MANAGEMENT Credit(s): 3

Curriculum